OpenWorldLab

Loading interactive view…

Induction and circuits

Wireless power

Two coils each tuned with a capacitor to the same frequency can pass power across a gap far more effectively than untuned coils: the receiver’s resonance builds up a large current from a small shared flux. Phone chargers and electric toothbrushes work this way.

Before you look

Predict first: You pull the receiver from 6 cm to 12 cm away. What happens to the power reaching the load?

What you are looking at

A transmitting coil on the left driven at 100 kHz through a capacitor, and a receiving coil on the right with its own capacitor and a 5 Ω load. Both are tuned to 100 kHz.

Drag the receiver away and back while the clock runs. Its glow and the load’s current follow the distance.

The physics

Each side is a series LC circuit at resonance. The receiver’s current I2=jωMI1/Z2I_2 = j\omega M I_1/Z_2 reflects an impedance ω2M2/Z2\omega^2M^2/Z_2 back into the transmitter, so

I1=VZ1+ω2M2/Z2,Pload=12∣I2∣2RLI_1 = \frac{V}{Z_1 + \omega^2M^2/Z_2}, \qquad P_{\text{load}} = \tfrac12|I_2|^2R_L

With Z=r+j(ωL−1/ωC)Z = r + j(\omega L - 1/\omega C) for each side. The coupling is k=M/L1L2k = M/\sqrt{L_1L_2}. When k is larger than about 1/Q1Q21/\sqrt{Q_1Q_2}, where Q1Q_1 and Q2Q_2 are the two sides’ quality factors, the coils are over-coupled: the single resonance splits into two, at

f±=f01∓kf_\pm = \frac{f_0}{\sqrt{1 \mp k}}

Going deeper

Vector calculus and Maxwell’s equations

Two coupled resonators behave like two pendulums joined by a spring: their shared modes swing in step and against each other, at different frequencies. Kurs and colleagues used this in 2007 to light a 60 W bulb two metres away with coils tuned to 10 MHz.

What to measure

Load power against coupled-circuit theory

  1. Read the load’s power at 6 cm: about 2.25 W.
  2. Drag the receiver to 12 cm: about 0.24 W.
  3. Back at 6 cm, set the source to f₀/√(1 + k) (about 95 kHz): the load still gets about 1.2 W, at a frequency where untuned coils would give almost nothing.

What the model leaves out

  • Wires are perfect conductors with no inductance of their own, and nothing radiates: the circuit is lumped, which is right while it is much smaller than a wavelength. At 100 kHz the coils are 3 km shorter than a wavelength, so this is right.
  • Coils, rings and magnets are filament loops, each standing for a bundle of turns or a slice of a magnet’s surface current. Very close to a loop the field is a little lumpy; a few loop spacings away it is exact.
  • The wire’s resistance is its DC value; at 100 kHz the skin effect would raise it a little.

Things to try

  • Detune the receiver: change its capacitor by 10% and the power collapses.
  • Sweep the source’s frequency with the coils close together and find the two peaks.

References

  • A. Kurs, A. Karalis, R. Moffatt, J. D. Joannopoulos, P. Fisher and M. Soljačić (2007), Wireless power transfer via strongly coupled magnetic resonances, Science 317, 83.
  • D. J. Griffiths (2017), Introduction to Electrodynamics, 4th edition, Cambridge University Press.
  • P. Horowitz and W. Hill (2015), The Art of Electronics, 3rd edition, Cambridge University Press.

More experiments, and how the lab works, are in the lab’s overview.