OpenWorldLab

Loading interactive view…

Induction and circuits

Switching an inductor

An inductor resists any change in its current. Switch it on and the current creeps up over a time L/R; switch it off and the coil drives its current on at whatever voltage it takes: hundreds of volts from a 6 V battery, the spark at a switch’s contacts.

Before you look

Predict first: With 0.5 A flowing through the coil, you open the switch. The 1.2 kΩ resistor across the coil is the only way left for the current. How big is the voltage spike?

What you are looking at

A 6 V battery, a switch, 12 Ω and a 0.6 H inductor, with a 1.2 kΩ resistor across the coil and an ammeter. The clock runs at a tenth of real time.

Close the switch and watch the ammeter climb. Open it: the switch sparks and the inductor’s pill jumps to hundreds of volts, then dies away within a few milliseconds.

The physics

Seen from the coil, the battery with its 12 Ω (RR) and the 1.2 kΩ across the coil (RfR_f) act as one source with resistance Rth=R∥RfR_{th} = R\parallel R_f, the two in parallel. The coil’s current rises as

I(t)=VR(1−e−t/τ),τ=LRth≈50 msI(t) = \frac{V}{R}\left(1 - e^{-t/\tau}\right), \qquad \tau = \frac{L}{R_{th}} \approx 50\ \mathrm{ms}

When the switch opens, the current I0I_0 must keep flowing for a moment, through RfR_f:

VL(t)=−I0Rf e−tRf/LV_L(t) = -I_0R_f\,e^{-tR_f/L}

The energy 12LI02\tfrac12 LI_0^2, 75 mJ here, ends up as heat in RfR_f. Without RfR_f it would go into a spark across the switch.

Going deeper

Vector calculus and Maxwell’s equations

The coil’s magnetic field holds the energy: 12LI2=∫B2/2μ0 dV\tfrac12 LI^2 = \int B^2/2\mu_0\,dV. An inductor cannot change its current instantly for the same reason a mass cannot change its velocity instantly; the voltage across it is L dI/dtL\,dI/dt. Car ignition coils, electric fences and switch-mode power supplies all use the switch-off spike.

What to measure

τ = L/R; the flyback spike I₀R_f

  1. Close the switch: after 50 ms the coil’s current should be 63% of 0.5 A.
  2. Wait a second, then open it: the inductor’s voltage jumps to about −600 V.
  3. After L/R_f = 0.5 ms it is down to 37% of that.

What the model leaves out

  • Wires are perfect conductors with no inductance of their own, and nothing radiates: the circuit is lumped, which is right while it is much smaller than a wavelength.
  • The switch opens instantly and cleanly. A real switch arcs and the arc’s resistance changes as it burns.
  • The inductor is a symbol with a value; the Coil part gives one with a shape and a field.

Things to try

  • Make the resistor across the coil 12 kΩ: the spike is ten times higher and ten times shorter.
  • Replace the 1.2 kΩ with a lamp: it flashes at switch-off.

References

  • P. Horowitz and W. Hill (2015), The Art of Electronics, 3rd edition, Cambridge University Press.
  • D. J. Griffiths (2017), Introduction to Electrodynamics, 4th edition, Cambridge University Press.
  • E. M. Purcell and D. J. Morin (2013), Electricity and Magnetism, 3rd edition, Cambridge University Press.

More experiments, and how the lab works, are in the lab’s overview.