OpenWorldLab

Loading interactive view…

Induction and circuits

Thomson’s jumping ring

Elihu Thomson showed in 1887 that a metal ring on an AC electromagnet leaps into the air when the current is switched on. The alternating flux drives a current round the ring that runs against the coil’s, and opposite currents repel.

Before you look

Predict first: You cut a slot through the ring and switch on again. What happens?

What you are looking at

A 200-turn coil standing upright, with an aluminium ring resting round its top. The coil is wired to a 120 V, 400 Hz source through a switch. The clock runs at a twentieth of real time.

Click the switch. The coil and the ring glow with their currents; ⊙ and ⊗ show that they run opposite ways. The ring shoots up, falls back and bounces.

The physics

The coil’s current Iccos⁡ωtI_c\cos\omega t links flux MIcMI_c through the ring. The ring, with resistance R and inductance L, carries

Ir=ωMIcR2+ω2L2I_r = \frac{\omega M I_c}{\sqrt{R^2 + \omega^2L^2}}

and lags the EMF by arctan⁡(ωL/R)\arctan(\omega L/R). The force between them averages to

Fˉ=−12Ic2 ω2MLR2+ω2L2 dMdz\bar F = -\frac12 I_c^2\,\frac{\omega^2 ML}{R^2 + \omega^2L^2}\,\frac{dM}{dz}

Above the coil dM/dz<0dM/dz < 0, so the force is upward. Without the lag (ωL≪R\omega L \ll R) the current would be in step with the EMF, a quarter cycle out of step with the coil’s current, and the force would average to zero: the repulsion comes from the ring’s inductance.

Going deeper

Vector calculus and Maxwell’s equations

At high frequency (ωL≫R\omega L \gg R) the ring keeps the flux through it almost constant, like a superconductor, and the force tends to −12Ic2M (dM/dz)/L-\tfrac12 I_c^2 M\,(dM/dz)/L. That is the principle of magnetic levitation over an AC coil, and of the induction motor.

What to measure

Ring current and mean force against phasor theory

  1. With the ring held (Motion: Held), read its current: about 1400 A peak, against the formula from M, L and R.
  2. Read the force pill: it averages about 3.2 N upward, against a weight of 0.42 N.
  3. Tick “Cut through”: the force is zero.

What the model leaves out

  • There is no iron anywhere: every coil here has an air core. Real jumping-ring demonstrations put an iron core through the coil and run on mains at 50 Hz; without iron the lab drives the coil harder and faster to make the same leap.
  • Coils, rings and magnets are filament loops, each standing for a bundle of turns or a slice of a magnet’s surface current. Very close to a loop the field is a little lumpy; a few loop spacings away it is exact.
  • The ring carries a uniform current over its cross-section; at 400 Hz the skin depth in aluminium, 4 mm, is close to the wall, so a real ring’s current crowds a little to its inside.

Things to try

  • Change the ring to copper: lower resistance, larger current, a higher jump, though it is heavier.
  • Halve the frequency: the force drops sharply, because ωL/R falls.

References

  • E. Thomson (1887), Novel phenomena of alternating currents, Electrical World 9, 258.
  • E. M. Purcell and D. J. Morin (2013), Electricity and Magnetism, 3rd edition, Cambridge University Press.
  • R. P. Feynman, R. B. Leighton and M. Sands, The Feynman Lectures on Physics, Volume II.

More experiments, and how the lab works, are in the lab’s overview.