OpenWorldLab

Loading interactive view…

Induction and circuits

The eddy-current pendulum

Swing a sheet of aluminium through the gap of a magnet and it stops as if it had hit syrup. No part of the plate is a circuit, yet currents swirl round inside it, and the field pushes back on them. Cut the plate into fingers and the swirls have nowhere to go: the slotted plate swings on.

Before you look

Predict first: The slotted plate has lost a fifth of its metal. How much of the solid plate’s braking does it keep?

What you are looking at

Two pendulums, aluminium plates 10 cm square on 30 cm arms, released together from 35°. Each swings through the poles of its own magnet: the dashed red circle is the near pole’s face, 3 cm across, with 0.12 T between the poles, into the board.

While a plate crosses the field, its eddy currents are drawn as their paths, each contour carrying an eighth of the solid plate’s strongest current: coral loops run clockwise, blue anticlockwise. They come in pairs, one on each side of the pole, and they move with it.

The physics

Metal moving at v\mathbf v through a field B\mathbf B feels v×B\mathbf v\times\mathbf B on its electrons. Charge piles up at the field region’s sides until, with the electric field it makes, the current is

J=σ(−∇φ+v×B),∇⋅J=0\mathbf J = \sigma\left(-\nabla\varphi + \mathbf v\times\mathbf B\right), \qquad \nabla\cdot\mathbf J = 0

with no current through any edge. Across the pole the current runs with v×B\mathbf v\times\mathbf B; outside it runs back. The field pushes on the part inside, against the motion. For a large sheet of thickness dd and conductivity σ\sigma over a round pole of uniform field B and radius a, half of v×B\mathbf v\times\mathbf B survives inside and the drag is

F=12 σd B2 πa2 vF = \tfrac12\,\sigma d\,B^2\,\pi a^2\, v

proportional to speed, like a viscous drag. The power it takes, FvFv, is the Joule heat ∫J2/σ dV\int J^2/\sigma\,dV.

Going deeper

Vector calculus and Maxwell’s equations

The lab solves ∇2φ=∇⋅(v×B)\nabla^2\varphi = \nabla\cdot(\mathbf v\times\mathbf B) on the plate itself, with ∂φ/∂n=(v×B)⋅n\partial\varphi/\partial n = (\mathbf v\times\mathbf B)\cdot\mathbf n on every edge, slot edges included, by finite volumes on 2.5 mm cells. For any round field on a round sheet of radius R the drag power has the closed form σdv2(12∫B2dA−Φ2/2πR2)\sigma d v^2\left(\tfrac12\int B^2 dA - \Phi^2/2\pi R^2\right): the second term is the rim, which forces the return current to flow back through the field region. The check measures that to 0.2%.

Slots work because the drag needs loops as big as the pole. A finger of width w carries only loops of size w where the field’s edge crosses it, and their drag shrinks roughly as (w/a)2(w/a)^2. Transformer cores are stacks of thin, insulated sheets for the same reason.

What to measure

Drag on a sheet ½σdB²πa²v; energy lost = Joule heat

  1. Watch both plates for three seconds: the solid one stops within two swings; the slotted one still swings through more than 30°.
  2. Read the heat under each: the solid plate’s heat equals the energy its swing has lost.
  3. Compare the two plates’ eddy currents as they cross the pole: the slotted plate’s are a few small loops at the ends of its fingers.

What the model leaves out

  • The eddy currents’ own magnetic field is left out. That is right while σμ₀vd is small, about 10⁻³ here; a thick copper plate at high speed would also be pushed sideways.
  • The pole’s field is uniform across a disc and falls to zero over a quarter of its radius; a real magnet’s fringe reaches further.
  • No air drag and no friction at the pivot.

Things to try

  • Switch to copper: it conducts 1.6 times better but is 3.3 times denser, so the plate stops more slowly. What matters is σ/ρ, conductivity over density.
  • Halve the field: the drag falls four times, as B².
  • Release from 10°: the plate spends its whole swing over the pole and creeps to rest without overshooting.

References

  • H. D. Wiederick, N. Gauthier, D. A. Campbell and P. Rochon (1987), Magnetic braking: simple theory and experiment, American Journal of Physics 55, 500.
  • D. J. Griffiths (2017), Introduction to Electrodynamics, 4th edition, Cambridge University Press.
  • E. M. Purcell and D. J. Morin (2013), Electricity and Magnetism, 3rd edition, Cambridge University Press.

More experiments, and how the lab works, are in the lab’s overview.