OpenWorldLab

Loading interactive view…

Induction and circuits

A DC motor

A coil carrying current in a magnetic field feels a torque that turns it until it faces across the field. A motor keeps it turning: every half turn a split ring on the shaft reverses the coil’s connection, so the torque never changes sign. And a turning coil is a generator, so the faster it spins, the more it pushes back on the battery.

Before you look

Predict first: You double the battery’s voltage. What happens to the motor’s top speed with no load?

What you are looking at

An end view: the shaft points out of the screen, the north pole on the left and the south on the right. The coil, 60 turns 4 cm by 3 cm, is seen edge-on; its two sides carry current out of the screen (⊙) and into it (⊗), and red arrows show the force on each.

At the centre the split ring turns with the coil, and two brushes touch it from the battery’s + and − terminals. Watch the ⊙ and ⊗ swap as a gap passes a brush: that happens just as the coil faces across the field, where the torque would otherwise reverse.

The motor is in slow motion: with no load it turns about 5,000 times a minute. The traces show its speed and the current it draws as it spins up.

The physics

With its normal at θ from the field, a coil of N turns and area A carrying current i feels a torque NBA isin⁡θNBA\,i\sin\theta. Turning at ω, it makes an EMF NBA ωsin⁡θNBA\,\omega\sin\theta. Through the commutator both carry ∣sin⁡θ∣|\sin\theta|, so with k(θ)=NBA∣sin⁡θ∣k(\theta) = NBA|\sin\theta|:

V=iR+Ldidt+k(θ) ω,Jdωdt=k(θ) i−τloadV = iR + L\frac{di}{dt} + k(\theta)\,\omega, \qquad J\frac{d\omega}{dt} = k(\theta)\,i - \tau_\text{load}

Here JJ is the rotor’s moment of inertia and LL the coil’s inductance. Averaged over a turn, kˉ=2πNBA\bar k = \tfrac{2}{\pi}NBA and k2‾=12(NBA)2\overline{k^2} = \tfrac12(NBA)^2. Setting the mean torque equal to the load gives the steady speed

ω=kˉ V−R τloadk2‾,ω0=4VπNBA\omega = \frac{\bar k\,V - R\,\tau_\text{load}}{\overline{k^2}}, \qquad \omega_0 = \frac{4V}{\pi NBA}

Speed falls in a straight line with load, from ω0\omega_0 with none to zero at the stall torque kˉV/R\bar kV/R. At 6 V and 0.2 T: 5,070 rpm free, 18.3 mN·m at stall, 2 A drawn at stall.

Going deeper

Vector calculus and Maxwell’s equations

The motor is an energy converter. The battery delivers ViVi; the winding turns i2Ri^2R into heat; the rest, kωik\omega i, is the back EMF times the current, and that is exactly the mechanical power τω\tau\omega. With no load, the back EMF nearly cancels the battery and the current is small. Stalled, there is no back EMF and the full V/RV/R flows: the reason a jammed motor burns out.

With slip rings instead of a split ring, the coil’s current never reverses. The torque swings the coil one way, then the other, and it settles where its normal lines up with the field, as a compass needle would.

What to measure

No-load speed 4V/πNBA; speed falls linearly with load

  1. Let the motor spin up with no load: its speed settles at 5,070 rpm, the dashed line.
  2. Set the load to 50% of the stall torque: the speed drops to half, 2,530 rpm, and the current rises to 1.19 A.
  3. Switch to slip rings: the coil rocks and stops facing across the field.

What the model leaves out

  • The poles’ field is uniform; a real motor has curved poles and an iron armature that make the field radial, so the torque hardly ripples.
  • The brushes switch instantly and never spark; the current through them stays continuous.
  • No friction; the load is a steady torque against the rotation.

Things to try

  • Double the field: the motor runs at half the speed with no load, but its stall torque doubles.
  • Set the load to 100%: the motor stalls and draws the full V/R.
  • Lower the voltage: speed falls in proportion, and the stall torque with it.

References

  • A. Hughes and B. Drury (2019), Electric Motors and Drives, 5th edition, Newnes.
  • E. M. Purcell and D. J. Morin (2013), Electricity and Magnetism, 3rd edition, Cambridge University Press.
  • D. J. Griffiths (2017), Introduction to Electrodynamics, 4th edition, Cambridge University Press.

More experiments, and how the lab works, are in the lab’s overview.