Induction and circuits
Displacement current
Current flows along the wire into a capacitor, but none crosses the gap between its plates. Ampère’s law ties the magnetic field round a loop to the current through it, so what does a loop round the gap measure? Maxwell’s answer: a changing electric field counts as a current too. Here the lab works out the field from the currents alone and lets you test his answer with a loop of your own.
Before you look
Predict first: An Ampère loop round the gap, as wide as the plates. While the capacitor charges, what is ∮B·dl round it?
What you are looking at
A side view: the wire runs left to right along the axis, through two round plates 16 cm across and 2 cm apart. The source charges the capacitor through 10 kΩ, then lets it discharge.
Gold dots are the current; + and − pile up on the plates, and amber arrows are the field between them. Cyan ⊙ above the axis and ⊗ below are B, curling round the axis, sized by its strength. B curls round the gap as well as round the wire.
The yellow ellipse is an Ampère loop seen at a slant. Drag it along the axis or drag its top to resize it. Choose a flat surface on it, or a bag that bulges through the gap; the bars compare the current through the surface with ∮B·dl round its rim.
The physics
Ampère’s law with Maxwell’s term:
For ideal plates of radius a, inside them, so : the displacement current between the plates equals the current in the wire. A loop of radius r < a in the gap encloses .
The surface is any surface with the loop as its rim. A flat disc round the wire is pierced by the current; a bag through the gap is not, but the changing E crosses it instead. Both give the same total.
Going deeper
Vector calculus and Maxwell’s equations
The lab does not assume Ampère’s law. It computes B from the conduction currents alone, by Biot–Savart, for the wire and the radial currents that spread charge over each plate; at these speeds that is exact (Jefimenko’s equations reduce to it). It computes E from the charges alone, by Coulomb. ∮B·dl/μ₀ and then come from separate calculations, and agree to 10⁻¹⁴.
Without Maxwell’s term, would demand , which a charging capacitor breaks. With it, the equations conserve charge, and they allow a wave of E and B that moves at : light.
What to measure
∮B·dl/μ₀ = I + ε₀dΦ_E/dt through any surface on the loop
- Put the loop round the wire, left of the plates: ∮B·dl/μ₀ is 99% of the wire’s current (the rest is the field fringing out to the loop).
- Move it into the gap, 4 cm across: no current crosses it, yet ∮B·dl/μ₀ is 22% of the wire’s current, all of it displacement current. (Ideal plates would give r²/a² = 25%; the field fringes.)
- Switch to the bulging surface on a loop round the wire: the conduction current through it falls to zero and the displacement current takes its place.
What the model leaves out
- The plates’ charge is spread evenly; real plates crowd it towards their edges.
- Quasi-static: the time constant is 89 ns, light crosses the board in a nanosecond, and nothing radiates. The movie is slowed about ten million times.
- The wires are 4 m long each way, ending where the source’s charge comes from.
Things to try
- Make the loop wider than the plates in the gap: it catches nearly all the displacement current.
- Switch to the sine source: B and the displacement current swing together, a quarter cycle ahead of the charge.
- Put the loop just outside a plate, round the wire: the displacement current through a flat disc there runs backwards, and the conduction current makes up for it.
References
- J. C. Maxwell (1865), A dynamical theory of the electromagnetic field, Philosophical Transactions of the Royal Society 155, 459.
- D. J. Griffiths (2017), Introduction to Electrodynamics, 4th edition, Cambridge University Press.
- D. J. Griffiths and M. A. Heald (1991), Time-dependent generalizations of the Biot–Savart and Coulomb laws, American Journal of Physics 59, 111.
- E. M. Purcell and D. J. Morin (2013), Electricity and Magnetism, 3rd edition, Cambridge University Press.
More experiments, and how the lab works, are in the lab’s overview.
